|
剛學不久~
我要做24H製的時鐘~但我一直DEBUG~一直用不出來~
我Xilinx ISE 8.2i軟體~
請會的人幫我看一下哪出錯了~謝
library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
use IEEE.STD_LOGIC_ARITH.ALL;
use IEEE.STD_LOGIC_UNSIGNED.ALL;
---- Uncomment the following library declaration if instantiating
---- any Xilinx primitives in this code.
--library UNISIM;
--use UNISIM.VComponents.all;
entity CLOCK_00_60 is
Port ( CLK : in STD_LOGIC;
RESET : in STD_LOGIC;
ENABLE : out STD_LOGIC_VECTOR (6 downto 0);
SEGMENT : out STD_LOGIC_VECTOR (6 downto 0));
end CLOCK_00_60;
architecture Behavioral of CLOCK_00_60 is
signal SCAN_CLK :STD_LOGIC;
signal COUNT_CLK :STD_LOGIC;
signal DECODE_BCD :STD_LOGIC_VECTOR (3 downto 0);
signal mineable :STD_LOGIC;
signal hreable :STD_LOGIC;
signal POSITION:STD_LOGIC_VECTOR (6 downto 0);
signal DIVIDER:STD_LOGIC_VECTOR (29 downto 1);
signal COUNT_BCD:STD_LOGIC_VECTOR (23 downto 0);
begin
-------------------------------------------------
process (CLK,RESET)
begin
if RESET = '0' then
DIVIDER <= ( others => '0');
elsif CLK' event and CLK = '1' then
DIVIDER <= DIVIDER + 1 ;
end if;
end process;
COUNT_CLK<=DIVIDER(24);
SCAN_CLK<=DIVIDER(15);
------------------------------------------------秒
process(RESET,SCAN_CLK)
begin
if RESET = '0' then
COUNT_BCD <= ( others => '0');
elsif SCAN_CLK' event and SCAN_CLK = '1' then
if COUNT_BCD(3 downto 0)= x"9" then
COUNT_BCD(3 downto 0)<= x"0";
COUNT_BCD(7 downto 4)<= COUNT_BCD(7 downto 4)+1;
else
COUNT_BCD(3 downto 0)<= COUNT_BCD(3 downto 0)+1;
end if;
end if;
end process;
mineable <= '1' when COUNT_BCD(7 downto 0) = x"59" else '0';
----------------------------------------------------------分
process(RESET,SCAN_CLK)
begin
if RESET = '0' then
COUNT_BCD <= ( others => '0');
if mineable = '1' then
elsif SCAN_CLK' event and SCAN_CLK = '1' then
if COUNT_BCD(11 downto 8)= x"9" then
COUNT_BCD(11 downto 8)<= x"0";
COUNT_BCD(15 downto 12)<= COUNT_BCD(15 downto 12)+1;
else
COUNT_BCD(11 downto 8)<= COUNT_BCD(11 downto 8)+1;
end if;
end if;
end if;
end process;
hreable <= '1' when COUNT_BCD(15 downto 8) = x"59" else '0';
-------------------------------------------------------------時
process(RESET,SCAN_CLK)
begin
if RESET = '0' then
COUNT_BCD <= ( others => '0');
if mineable = '1' and hreable = '1' then
elsif SCAN_CLK' event and SCAN_CLK = '1' then
if COUNT_BCD(19 downto 16)= x"9" then
COUNT_BCD(19 downto 16)<= x"0";
COUNT_BCD(23 downto 20)<= COUNT_BCD(23 downto 20)+1;
if COUNT_BCD(19 downto 16)= x"2" then
COUNT_BCD(23 downto 20)<= x"0";
else
COUNT_BCD(19 downto 16)<= COUNT_BCD(19 downto 16)+1;
end if;
end if;
end if;
end if;
end process;
process(RESET,SCAN_CLK)
begin
if RESET = '0' then
POSITION <= "1111110";
elsif SCAN_CLK' event and SCAN_CLK = '1' then
POSITION<="111111"&POSITION(0);
end if;
end process;
ENABLE<=POSITION;
-----------------------------------------------------------
process(POSITION,SCAN_CLK)
begin
case POSITION is
when "1111110" => DECODE_BCD <=COUNT_BCD(3 downto 0); --秒
when "1111101" => DECODE_BCD <=COUNT_BCD(7 downto 4); --秒
when "1111011" => DECODE_BCD <=COUNT_BCD(11 downto 8); --分
when "1110111" => DECODE_BCD <=COUNT_BCD(15 downto 12); --分
when "1101111" => DECODE_BCD <=COUNT_BCD(19 downto 16); --時
when "1011111" => DECODE_BCD <=COUNT_BCD(23 downto 20); --時
when others => null;
end case;
end process;
with DECODE_BCD Select
SEGMENT<= "1000000" when X"0",
"1111001" when X"1",
"0100100" when X"2",
"0110000" when X"3",
"0011001" when X"4",
"0010010" when X"5",
"0000010" when X"6",
"1111000" when X"7",
"0000000" when X"8",
"0010000" when X"9",
"1111111" when others;
end Behavioral;
|
加好友 
發短信
Post By：2010-12-19 14:00:46
